MCP-TY
大理石結晶粉
Marble Crystallizing Powder

特　　點
Features
本產品適應于各種天然大理石翻新后的晶硬處理及定期養護，該產品使用方便，可迅速使大理石表面達到光亮如鏡的效果，并增強石材表面的硬度及耐磨度。長時間使用，不會造成石材任何損壞，不影響石材透氣性及不改變石材天然色澤，定期只需作簡單的護理即可保持石材長期亮麗如新。
This product can be used for crystallizing processing and regular maintenance of various marble reconditioned. It is easy to use. It can make the marble surface bright and shining, and can enable the marble surface harder and more wearable. There will be no damage to the stone after long use. It will not influence the air conductivity of the stone and will not change the natural color and luster of the stone. Just a regular and simple maintenance will keep the stone as bright as new for a long period of time.

使用方法
How to use
1、 清除石材表面蠟層及污物。
2、 對石材已經磨損、表面凹凸不平或深度劃?rùn)M時，事先需將石材表面翻新打磨至平整光滑。
3、 將結晶粉加清水調成糊狀后均勻涂于石材表面，并噴灑適量清水使石材保持濕潤，然后用擦地機或?qū)Ｓ媒Y(jié)晶機配合白潔墊進行拋磨，（拋磨過程中至終保持地面濕潤，切勿過干），每次工作區域大約在3~5平米左右。
4、 待處理的石材表面形成亮麗的晶面后，用刮水器將漿狀物刮到下一個操作區域，并只需補加少量新的結晶粉繼續拋磨，此拋磨方法重復至地面出現大量泡沫時用吸水機吸盡，然后重新加新的結晶粉按以上方法進行操作。
5、 當?shù)孛嬲麄€(gè)結晶操作完成后，用清水洗凈并吸干。
1. Remove the wax layer and dirt on the stone surface.
2. If the stone has been worn, accidented or deeply lacerated, the stone surface shall be reconditioned and polished to be even and smooth in advance.
3. Mix the Crystallizing Powder with clear water. Then spread it on the stone surface, and spray a proper amount of clear water to keep the stone wet. Polish with a floor rubbing machine or special crystallizing machine together with a whitening cushion. (Always keep the floor wet during and never be too dry polishing. Each operation covers about 3~5 square meters. 
4. After a bright crystallizing surface is seen on the stone surface, scrape the pastry substance to the next operating area with a wiper. Continue to polish by adding only a bit of new crystallizing powder. Repeat such polishing till a lot of bubbles are seen on the floor and absorb them with a water sampling machine. Then, add new crystallizing powder again and operate by using the foregoing method.
5. Clean the floor with clear water and dry the floor when the entire crystallizing operation is completed.